15 YEARS UVC LED FACTORY 
+86-0755-29985915
Red 5mm LED Chip
Home » Products » DIP LED CHIP » 5mm THT LED » Red 5mm LED Chip

Product Category

Contact Information

 Offices: No.369,Baotian 1st Road, Tiegang, Xixiang, Bao'an, Shenzhen, China.

Telephone: +86-0755-29985915
Mobile: +86-189 2465 4005

 Email: info@tzuvcled.com

Contact us
Share to:

Red 5mm LED Chip

Availability:
Quantity:
  • Tuozhan

Specifications:


Welding temperature: 260 degrees

Welding time: within 3 seconds

Gel size: 5mm

Pin size: 25mm

Name: 5mm Dip LED Chip

Wavelength: 620--625nm

Brightness: 400--500mcd


ColorDominant Wavelength(nm)/(k)LuminousIntensity(mcd) Angle(Deg)Reverse Current(uA)VR=5VForward Voltage(V)Recommend Forward Current(Ma)POWER
 Red620-630nm600-80090-120deg52.0-2.2200.04w
Blue460-470nm1000-120090-120deg53.0-3.2200.06w
Green515-525nm2000-250090-120deg53.0-3.2200.06w
Orange600-605nm600-80090-120deg52.0-2.2200.04w
Yellow588-595nm600-80090-120deg52.0-2.2200.06w



Application:


Landscape lighting, toys, keyboard, router, crafts, gifts, stage decorations, LED Christmas trees, traffic signal lights, community lighting, LED street lights, general signs, household appliances, LED lighting, LED emergency lights, automotive industry, LED high bay lights, LED spotlights, LED decorative lights, LED barrier tubes, LED display screens and other industries and products are widely used in advertising media, transportation, education, sports, entertainment, exhibitions, shopping malls, squares, stations and other industries and places.


CE & RoHS Certification


Remark:

Electrostatic protection

1. The workbench touching the LED products should be covered with ESD wrist strap and grounded reliably;

2. Personnel must wear electrostatic wristbands (wired electrostatic rings) and protective gloves when touching LEDs, and wear anti-static clothes, electrostatic shoes and electrostatic caps when conditions permit;

3. The equipment that touches the LED during the application and processing must be reliably grounded, such as soldering iron, foot trimmer, foot bending machine, and welding equipment. If possible, a plasma fan can be installed to eliminate static electricity;

4. In use or when designing electronic circuits, the hazards of excessive current to LEDs must be considered.


LED installation method


1. Be sure not to install the LED when the pins are deformed

2. When installing the LED on the printed circuit board, the center distance of the holes on the circuit board should be the same as the center distance of the LED lamp pins. If the hole spacing is large, the lamp pins will have residual stress, and the resin part may be caused during soldering. Produce deformation

3. When the LED is inserted into the PCB board, the holes on the PCB board should match the size of the lamp pin to avoid being too large or too small;

4. It is recommended to use the guide sleeve for positioning when installing the LED;

5. The pad area of each solder foot of the double pin is not less than 4.6 square millimeters;

6. The area of each solder foot pad of Piranha is not less than 9.2 square millimeters;

7. The area of each solder foot pad of SMD ordinary single crystal bracket is not less than 3.9 square millimeters;

8. The area of each solder pad of the SMD three-in-one bracket is not less than 1.65 square millimeters;

9. For other types of lamps, the size of the pads should be determined according to the actual lamp structure.


Previous: 
Next: 

Quick Links

Specialized In Product

Contact Information

Contact:Info

Telephone: +86-0755-29985915
Mobile(Whatsapp): +86 18924654005

Send Email: info@tzuvcled.com

 Address: No.369,Baotian 1st Road, Tiegang, Xixiang, Bao'an, Shenzhen, China.
Follow Us
Copyright © 2020 Shenzhen Tuozhan Opto Electronics Co., Ltd. All Rights Reserved   Technology by leadong