Contact Information

 Offices: No.369,Baotian 1st Road, Tiegang, Xixiang, Bao'an, Shenzhen, China.

Telephone: +86-0755-29985915
Mobile: +86-189 2465 4005

 Email: info@tzuvcled.com

Contact us


Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

5mm Straw Hat RGB LED chip



Name: 5mm Straw Hat Full Color RBG Common Yin

Wavelength: R620 B520 g520nm

Brightness: R2000 B3000 G7000mcd

1. Appearance: round head, flat head, concave, straw hat, square, piranha, tower, steel helmet, oval, bullet, Christmas head, etc.;

2. Color: RGB, RBG, GBR (can be selected at will);

3. Appearance: transparent, foggy, colored colloid;

4. Features: fast flashing, slow flashing, cycle flashing, intermittent flashing, synchronous flashing, single flashing, double flashing, two-color, three-color, colorful, full-color, highlight, gradual flash, trigger flash, 2PIN dual-color non-polarity, 3PIN dual-color total Light-emitting diodes such as cathode and anode;

5. Uses: toys, Christmas decoration lights, string lights, lighting, spotlights, ceiling lights, flood lights, street lights, car lights, traffic lights, lighting lights, bulbs, flashlights, energy-saving lights, meteor shower lights, induction lights, etc.;

6. Specifications: 3mm, 5mm, 8mm, 10mm, 12mm, etc.;

7. Voltage: 3.0-4.5V, current: 20MA;

CE & RoHS Certification


1. Electrostatic protection

1. The workbench touching the LED products should be covered with protective electric tape and grounded reliably;

2. Personnel must wear electrostatic wristbands (wired electrostatic rings) and protective gloves when touching LEDs, and wear anti-static clothes, electrostatic shoes and electrostatic caps when conditions permit;

3. The equipment that touches the LED during the application and processing must be reliably grounded, such as soldering iron, foot trimmer, foot bending machine, and welding equipment. If possible, a plasma fan can be installed to eliminate static electricity;

4. In use or when designing electronic circuits, the hazards of excessive current to LEDs must be considered.

LED installation method

1. Be sure not to install the LED when the pins are deformed

2. When installing the LED on the printed circuit board, the center distance of the holes on the circuit board should be the same as the center distance of the LED lamp pins. If the hole spacing is large, the lamp pins will have residual stress, and the resin part may be caused during soldering. Produce deformation

3. When the LED is inserted into the PCB board, the holes on the PCB board should match the size of the lamp pin to avoid being too large or too small;

4. It is recommended to use the guide sleeve for positioning when installing the LED;

5. The pad area of each solder foot of the double pin is not less than 4.6 square millimeters;

6. The area of each solder foot pad of Piranha is not less than 9.2 square millimeters;

7. The area of each solder foot pad of SMD ordinary single crystal bracket is not less than 3.9 square millimeters;

8. The area of each solder pad of the SMD three-in-one bracket is not less than 1.65 square millimeters;

9. For other types of lamps, the size of the pads should be determined according to the actual lamp structure.


Contact Information

More >>

 Office Adress: No.369,Baotian 1st Road, Tiegang, Xixiang, Bao'an, Shenzhen, China.

 Mobile: +86-18598102007

 Email: info@tzuvcled.com

Contact us

Quick Links

Specialized In Product

Contact Information


Telephone: +86-18924654005
Mobile(Whatsapp): +86-18924654005

Send Email: info@tzuvcled.com

 Address: No.369,Baotian 1st Road, Tiegang, Xixiang, Bao'an, Shenzhen, China.
Follow Us
Copyright © 2020 Shenzhen Tuozhan Opto Electronics Co., Ltd. All Rights Reserved   Technology by leadong